>

Hot air hoses, high temperature hoses (-200 °C +1,100 °C) | CP HiTex 486 High-temperature hose, clamping profile hose, multilayer, insulating, suitable for slight overpressure (up to +700°C) -60°C to 650°C

Hot air hoses, high temperature hoses (-200 °C +1,100 °C)
PROTAPE® TPE 320 TPE hose, lightweight (up to +150°C) -40°C to 125°C
PROTAPE® TPE 321 REINFORCED TPE Hose, lightweight, fabric reinforced (up to +125°C) -40°C to 110°C
AIRDUC® TPE 363 TPE hose, medium weight (up to +150°C) -40°C to 125°C
NEO 390 ONE neoprene hose, single layer, tight (up to +150°C)
NEO 390 TWO neoprene hose, double layer, tight (up to +150°C)
CP HYP 450 clamp profile hose, (up to +170°C) -40°C to 170°C
CP PTFE/HYP-INOX 472 Clamp profile hose, double layer (up to +170°C) -40°C to 170°C
CP PTFE/HYP-INOX 472 EC Electrically conductive clamping profile hose, double-layer, highly resistant to chemicals (up to +170°C) -40°C to 170°C
CP VITON® 459 EC Electrically conductive clamping profile hose, (up to +210°C) -20°C to 210°C
CP PTFE-INOX 475 FOOD clamping profile hose, food and pharmaceutical hose, highly resistant to chemicals (up to +270°C)
CP PTFE-INOX 475 EC Electrically conductive clamping profile hose, highly resistant to chemicals (up to +270°C) -150°C to 250°C
CP PTFE/GLASS-INOX 471 Clamping profile hose, double layer, highly resistant to chemicals (up to +270°C) -150°C to 250°C
CP PTFE/GLASS-INOX 471 EC Electrically conductive clamping profile hose, double-layer, highly resistant to chemicals (up to +270°C) -150°C to 250°C
SIL 391 ONE Silicone tubing, single layer, tight (up to +280°C) -70°C to 260°C
SIL 391 TWO silicone hose, double layer, tight (up to +280°C) -70°C to 260°C
CP Kapton® 476 High temperature hose, clamping profile hose, (up to +400°C) -60°C to 400°C
CP HiTex 480 High temperature hose, clamping profile hose, (up to +450°C) -60°C to 400°C
CP HiTex 487 High temperature hose, clamping profile hose, (up to +500°C) 60°C to 450°C
CP HiTex 485 High-temperature hose, clamping profile hose, multilayer, insulating, suitable for slight overpressure (up to +550°C) -60°C to 500°C
CP HiTex 481 High-temperature hose, clamping profile hose, double-layer (up to +700°C) -60°C to 600°C
CP HiTex 486 High-temperature hose, clamping profile hose, multilayer, insulating, suitable for slight overpressure (up to +700°C) -60°C to 650°C
CP HiTex 483 High-temperature hose, clamping profile hose, multilayer, insulating (up to 1,100°C) -60°C to 900°C

The CP HiTex 486 high-temperature hose with clamping profile hose is multi-layer, insulating, suitable for slight overpressure.

The CP HiTex 486 high-temperature hose with clamping profile hose is multi-layer, insulating, hardly inflammable and suitable for slight overpressure. Flexible hose for hot and cold gases; for exhaust gas extraction or extraction of engine exhaust gases ecc. You will find all further detailed information about dimensions, stock information, prices and delivery times in our online shop. Test our efficiency!

Item no.
 
Label
 
Internal ∅
inch / mm
External ∅
mm
Excess pressure
bar
Negative pressure
bar
Bending radius
mm
Bearing length
Meter
Weight
kg
Stock
 
Price
?
Graduated price
 
quantity
 
 
 
 
 

Frequently asked questions (FAQ)

Exhaust gas hoses for exhaust gas extraction Applications and properties The exhaust hose is a flexible hose used to direct exhaust gases from vehicle engines and other equipment away from the operator. It is mainly used on vehicle exhaust systems, above- and underfloor extraction systems and engine test benches in industry and workshops. In order to guarantee smooth and faultless use, the hoses must have certain properties. Thereby hot gases up to several hundred ?Celsius must be able to be transported without damaging the material. A flexible hose shape is advantageous to resist vibrations and impact and balancing effects from outside. The following of our hose products meet these requirements and can be used without hesitation for the transport of exhaust gases:- PROTAPE? TPE 325 WEAR STRIP- PROTAPE? TPE 326 MEMORY- METAL HOSE 375- CP HYP 450 and CP HYP 450 PROTECT- CP ARAMID 461 and CP ARAMID 461 PROTECT- CP KAPTON? 476- CP HiTex 481, 483, CP HiTex 485, 486 and 487 Frequently asked questions Up to what maximum temperatures can the hoses be used? - Up to 120?C:?METAL HOE 37S5- up to 170?C:?CP HYP 450- to 200?C: PROTAPE? TPE 326 MEMORY* and CP HYP 450 PROTECT*- up to 220?C PROTAPE? TPE 325 WEAR STRIP- up to 300?C:?CP ARAMID 461 and CP ARAMID 461 PROTCTE*- up to 400?C: CP KAPTON? 476- up to 500?C: CP HiTex 487- up to 550?C:?CP HiTex 485- up to 700?C:?CP HiTex 481 and CP HiTex 486- up to 1100?C?CP HiTex 483*with 50% fresh air supply and correct use of exhaust gas funnels For which applications are the exhaust gas hoses suitable? The typical areas of application are the use in overfloor and underfloor extraction systems, suction slotted ducts and exhaust hose reels for the extraction of engine exhaust gases as well as exhaust gas measurement in vehicle exhaust systems. All the hoses listed in this section are suitable for these applications, whereby in workshops (motor vehicles), for example, the tread resistance of PROTAPE? TPE 326 MEMORY or the abrasion protection profile of CP HYP 450 PROTECT and CP ARAMID 461 PROTECT are advantageous. The CP HiTex 485 and CP HiTex 486 are insulating and suitable for slight overpressure. Technical details and standards The following hose types have an aramid wall which corresponds to fire protection class M1 according to UNE 23.727-90:- CP ARAMID 461- CP ARAMID 461 PROTECT The following hose types are flame-retardant according to DIN 4102-B1 - CP HiTex 481 Please contact us for technical advice!

The typical areas of application are the use in overfloor and underfloor extraction systems, suction slotted ducts and exhaust hose reels for the extraction of engine exhaust gases as well as exhaust gas measurement in vehicle exhaust systems. All the hoses listed in this section are suitable for these applications, whereby in workshops (motor vehicles), for example, the tread resistance of PROTAPE? TPE 326 MEMORY or the abrasion protection profile of CP HYP 450 PROTECT and CP ARAMID 461 PROTECT are advantageous. The CP HiTex 485 and CP HiTex 486 are insulating and suitable for slight overpressure.

Vibraplast AG offers its customers an assembly service of connecting parts. For a hose with assembled fittings an additional delivery time of 3 working days must be expected.?

CP Vibraplast CP clamp profile hoses (CP="Clamp Profile") are based on a special design that offers numerous product advantages, especially under high stress. In a clamp profile, strip materials are clamped in a single, double or even multiple layers in a spiral and an inserted wire prevents slipping out. These hoses are flexible, compressible, have external abrasion protection and can be extremely resistant to chemicals and/or heat, for example. We can adapt the construction and as a result the properties of the hose to your specific needs. This increases customer benefit, creates added value and often saves costs. Talk to us! Single layer Abrasion protection through external clamping profile (extra stable clamping profile): drop-shaped geometry ensures high Fl?chentr?gheitsmoment? high Scheiteldruckfestigkeit? high vacuum load capacity round Klemmprofil? high and even distribution of the Klemmkraft? no punctiform Spannungsspitzen? increased tightness Rounded clamping profile ends: Gentle deflection of the fabric/film high dynamic load capacity high overpressure load capacity Multilayer Multilayer wall construction selectable specific adjustment of the product properties better seal thermic isolation Sound insulation CP HYP 450 PROTECT, CP ARAMID 461 PROTECT Outer protection profile: made of elastic material as shock and abrasion protection can be supplied in any colour specially developed and protected geometry: firm clamping ensures safety against pushing off Thickening at the end of the profile offers additional safety against pushing off

TECHNICAL TERMS AND DEFINITIONS Abrasion Undesirable change of the surface due to loosening of small particles as a result of mechanical stress. Also generally known as wear. The abrasion is determined according to DIN 53516. Here, a specimen is guided with a certain contact pressure on a rotating roller covered with a test emery sheet. The total friction path is approx. 40 m. The loss in mass caused by abrasive wear is measured, taking into account the density of the test specimen and the attack of the emery sheet. The information is given as volume loss in mm?. Additives All components in a plastic formulation which are not polymers or their precursors and which are only added in relatively small quantities (UV stabilizers, flame retardants, conductive carbon black, etc.) Aging The totality of all chemical and physical processes irreversibly taking place in a material over time. This usually leads to a deterioration of the service properties. Heat, light, high-energy radiation, chemicals, weather, oxygen (ozone) are frequent causes of ageing. The aging condition, mostly surface attack, is monitored by changes in material properties such as toughness, turbidity, molecular weight, etc. Bending radius Smallest permissible radius when laying a hose line. The bending radius is given in mm and always refers to the inside of the hose bend. Compression set The determination of the compression set DVR [%] according to DIN 53517 is a creep test over 24 hours at 70 ?C and 72 hours at room temperature with constant deformation. The permanent deformation is measured after the specimen is unloaded again. Elasticity Means the ability of a material to reshape after removal of an externally applied mechanical stress. Elastomers Designation for wide-meshed, cross-linked, macromolecular substances which can be stretched by at least twice their original length by the application of a slight force at room and higher temperatures and which, once the force has been removed, return rapidly and practically completely to their original form. Flame retardants Are plastic additives which reduce the flammability and combustibility of plastics. Flame retardants can intervene in the combustion mechanism either physically by cooling, coating and diluting or chemically by reaction in the gas phase (elimination of the energy-rich radicals supporting combustion) or in the solid phase (formation of a protective coal or ash layer). Flexibility Force required to achieve the minimum bending radius (the greater the force required, the less flexibility). Flow / Creep The delayed but still reversible deformation of a viscoelastic material under constant load is called creep. The irreversible deformation occurring at higher loads is called flow (in cold state). The flow process leads to failure of the component under unchanged load. Gas permeability Passage of a gas through a test sample. This takes place in three steps: Dissolving the gas in the sample. Diffusion of the dissolved gas through the sample. ? Evaporation of the gas from the sample. The permeation coefficient is a material constant which indicates which volume of gas passes through a test specimen of known area and thickness at a given partial pressure difference in a given time. It depends on the temperature and is determined according to DIN 53 536. Halogens The elements fluorine (F), chlorine (Cl), bromine (Br) and iodine (I) form the group of halogens. Hardness Hardness is the resistance of a material to the penetration of a body of a certain shape and defined spring force. The penetration depth of the test body is a measure of hardness. The hardness of elastomers is determined according to Shore A or Shore D in accordance with DIN 53505. It is given as a whole number from 0 to 100 and the letters A and D. The larger the number, the higher the hardness. Hydrolysis resistance Hydrolysis = irreversible splitting of the polyester chains in ester polyurethanes. It is caused by prolonged storage in warm water, saturated steam, tropical climate (moisture in combination with heat), aggressive chemicals or aggressive wood dusts. The consequence of hydrolysis is a decrease in mechanical strength properties. Ether polyurethanes are resistant to hydrolysis. Microbe resistance Ester polyurethanes can be destroyed by long-term contact with earth-like substances or heavy contamination under conditions favourable to microbes, as the enzymes released by the organisms damage the chemical bonds. Under very unfavourable conditions, initial damage occurred after 8-24 weeks. This time can be delayed by adding toxic fungicides, but later on, by leaching and leaching of the additive, the value may fall below the limit required for protection. It is of the utmost concern that the often toxic fungicides inevitably migrate to the surface and come into contact with the user or conveyed material. Such solutions do not meet our quality level and are therefore not part of our product range. Our hoses made of ether polyurethane are permanently not attacked by microbes and are the clearly better solution here. Specific volume resistance According to TRGS 727 the volume resistivity RGES = R?A/S [??m] must be determined. Where R is the measured resistance, A is the surface area of the electrode and S is the thickness of the reed between the plastic and the wire. A piece of hose 100 mm long with a cylindrical electrode inserted on one side is measured, with the counter electrode forming the steel wire helix. The volume resistivity determined thereby must be RGES < 2.5 x 1018 Ohm. Surface resistivity The surface resistance (Ro) indicates the insulating capacity of the insulating material surface. Ro is reduced in plastics by the formation of a water film which is created by the action of hydrophilic groups (-COOH, -NH2, -OH), plasticizers and organic fillers. Ro is determined at a test voltage of 1 kV between two electrodes (spring-loaded metal blades) located at a distance of 10 mm. Ro is given either in ohms or as a comparative figure, e.g. 10 = Ro < 10 or comparative figure 6; 10 = Ro < 10 or comparative figure 11. Permeation The passage of a gas through a sample is called permeation. It takes place in three steps: Dissolving the gas in the sample Diffusion of the dissolved gas through the sample Evaporation of the gas from the sample The permeation coefficient Q in m?/(s * Pa) is a material constant which indicates the gas volume ? passes through a test specimen of known area and thickness at a given partial pressure difference in a given time. It depends on the temperature and is determined according to DIN 53536. Swelling Absorption of liquid and gaseous substances into solids without a chemical reaction taking place between them. The consequences are an increase in volume and weight combined with a corresponding decrease in mechanical values. After evaporation of the penetrated substance and the associated decrease in swelling, the original properties of the product are almost restored. The swelling is therefore a reversible process. Peak compressive strength Resistance to compression of suction and discharge hoses by external load applied at the apex. Water vapour permeability It is characterised by the amount of water vapour that passes through 1 m? of sample surface in 24 hours under defined conditions and is approximately inversely proportional to the sample thickness. The water vapour permeability WDD in g/(m?*d) of a plastic is determined according to DIN 53122 sheet 1. Tear resistance Tear propagation resistance is the resistance that a notched test piece offers to tear propagation. The test is carried out in accordance with DIN 53515 on angle specimens which are provided with a notch on one side. UV radiation Depending on the duration and intensity, plastics can be chemically degraded by the action of UV radiation (ageing). Polyurethanes generally have a good UV resistance. In the course of time, the material turns yellow, which does not automatically cause a decrease in the mechanical properties. With the help of UV stabilizers and/or color pigmentation a certain stabilization can be achieved. We offer special hose solutions for increased and strong UV- exposure. Please contact us in such cases.

By using this website, you consent to the use of cookies and our privacy policy. Privacy policy agree.
If you have any questions, please contact info@vibraplast.ch

This content is reloaded